model pba15f-3r3 pba15f-5 pba15f-9 pba15f-12 pba15f-15 PBA15F-24 pba15f-48 max output wattage[w] 9.9 15 15.3 15.6 15 16.8 16.8 dc output 3.3v 3a 5v 3a 9v 1.7a 12v 1.3a 15v 1a 24v 0.7a 48v 0.35a specifications model pba15f-3r3 pba15f-5 pba15f-9 pba15f-12 pba15f-15 PBA15F-24 pba15f-48 input voltage[v] ac85 - 264 1 f or dc110 - 370 ( ac50 or dc70 please refer to the instruction manual 2.1 input voltage * 3 ) current[a] acin 100v 0.30typ ( io=100% ) 0.4typ ( io=100% ) acin 200v 0.15typ ( io=100% ) 0.2typ ( io=100% ) frequency[hz] 50/60 ( 47 - 440 ) or dc efficiency[%] acin 100v 68typ 74typ 75typ 75typ 77typ 75typ 75typ acin 200v 68typ 75typ 77typ 78typ 80typ 78typ 78typ inrush current[a] acin 100v 15typ ( io=100% )( at cold start ) acin 200v 30typ ( io=100% )( at cold start ) leakage current[ma] 0.15/0.30max ( acin 100v/240v 60hz , io=100% , according to iec60950-1 , denan ) output voltage[v] 3 . 35 9 1 21 52 44 8 current[a] 3 3 1.7 1.3 1 0.7 0.35 line regulation[mv] 20max 20max 36max 48max 60max 96max 192max load regulation[mv] 40max 40max 100max 100max 120max 150max 240max ripple[mvp-p] 0to+50 c * 1 80max 80max 120max 120max 120max 120max 150max -10 - 0 c * 1 140max 140max 160max 160max 160max 160max 200max ripple noise[mvp-p] 0to+50 c * 1 120max 120max 150max 150max 150max 150max 250max -10 - 0 c * 1 160max 160max 180max 180max 180max 180max 300max temperature regulation[mv] 0to+50 c 50max 50max 90max 120max 150max 240max 480max -10to+50 c 60max 60max 120max 150max 180max 290max 600max drift[mv] * 2 20max 20max 36max 48max 60max 96max 192max start-up time[ms] 200typ ( acin 100v , io=100% ) * start-up time is 700ms typ for less than 1minute of applying input again from turning off the input voltage. hold-up time[ms] 20typ ( acin 100v , io=100% ) output voltage adjustment range[v] 2.85 - 3.60 4.50 - 5.50 7.50 - 10.0 10.0 - 13.2 13.2 - 18.0 19.2 - 27.0 39.0 - 53.0 output voltage setting[v] 3.30 - 3.40 5.00 - 5.15 9.00 - 9.36 12.00 - 12.48 15.00 - 15.60 24.00 - 24.96 48.00 - 49.92 protection circuit and others overcurrent protection works over 105% of rated current and recovers automatically overvoltage protection[v] 4.00 - 5.25 5.75 - 7.00 11.5 - 14.0 15.0 - 18.0 20.0 - 25.0 30.0 - 37.0 58.0 - 65.0 operating indication led ( green ) remote on/off none isolation input-output ac3 , 000v 1minute , cutoff current = 10ma , dc500v 50m w min ( at room temperature ) input-fg ac2 , 000v 1minute , cutoff current = 10ma , dc500v 50m w min ( at room temperature ) output-fg ac500v 1minute , cutoff current = 25ma , dc500v 50m w min ( at room temperature ) environment operating temp. , humid.and altitude -10 to +71 c ( required derating ), 20 - 90%rh ( non condensing ) 3 , 000m ( 10 , 000feet ) max storage temp. , humid.and altitude -20 to +75 c , 20 - 90%rh ( non condensing ) 3 , 000m ( 10 , 000feet ) max vibration 10 - 55hz , 19.6m/s 2 ( 2g ), 3minutes period , 60minutes each along x , y and z axis impact 196.1m/s 2 ( 20g ), 11ms , once each x , y and z axis safety and noise regulations agency approvals ( at only ac input ) ul60950-1 , c-ul ( csa60950-1 ), en60950-1 , en50178 complies with den-an conducted noise complies with fcc part15 classb , vcci-b , cispr22-b , en55011-b , en55022-b ce marking low voltage directive , emc directive harmonic attenuator complies with iec61000-3-2 ( not built-in to active filter * 4 ) others case size/weight 31 x 78 x 85mm ( without terminal block )( w x h x d ) / 200g max ( without cover ) cooling method convection *1 measured by 20mhz oscilloscope or ripple-noise meter(equivalent to keisoku-giken :rm101). *2 drift is the change in dc output for an eight hour period after a half-hour warm-up at 25 c. * 3 derating is required. * 4 when two or more units are used,they may not comply with the harmonic attenuator. please contact us for details. * parallel operation with other model is not possible. * derating is required when operated with cover. * a sound may occur from power supply at peak loading. pba15f unit type pb a 15 f - o -o ordering information 1 series name 2 single output 3 output wattage 4 universal input 5 output voltage 6 optional c :with coating g :low leakage current e :low leakage current and emi class a t :vertical terminal block j :connector type n :with cover (ul508 is pending for approval) n1 :with din rail v :output voltage setting potentiometer external- ly r 123456 pb a-6 recommended noise filter nac-06-472 high voltage pulse noise type : nap series low leakage current type : nam series *the noise filter is recommended *to connect with several devices. cover is optional distribution: rsg electronic components gmbh sprendlinger landstr. 115 d-63069 offenbach/germany tel. +49 69 984047-0 fax +49 69 984047-77 info@rsg-electronic.de www.rsg-electronic.de ?nderungen vorbehalten / subject to change without notice
2.5 point a:c102 cover (option) name plate m3 mounting hole 2-m3 mounting hole 2-m3 ac(n) ac(l) fg -v +v terminal cover 15.1 1.5 5 18 31 34.5 34.5 78 36.5 11.5 85 16.5 2 70.5 12.2 1.5 18 22.6 1.5 31 0.5 60 0.5 9.5 7.5 pba15f pbw15f led voltage adjust cover name plate ? tolerance : 1 ? mass : 200g or less (without cover) ? pcb material/thickness : cem3 / 1.6mm ? chassis material : electric galvanizing steel board ? dimensions in mm ? mounting torque : 0.6n ? m(6.3kgf ? cm)max ? screw tightening torque : m3 0.8n ? m(8.5kgf ? cm)max ? please connect safety ground to the unit in 2-m3 holes. ? external size of option t,j,n,n1 and v is different from standard model and refer to 7 option of instruction manual for details. pb a-7 pba15f block diagram 2.5a ac250v ac in dc out fg 85 - 264v noise filter inverter control current sensing rectifier and filter control photocoupler photocoupler transformer inrush current limit fuse over voltage protection rectifier and filter external view distribution: rsg electronic components gmbh sprendlinger landstr. 115 d-63069 offenbach/germany tel. +49 69 984047-0 fax +49 69 984047-77 info@rsg-electronic.de www.rsg-electronic.de ?nderungen vorbehalten / subject to change without notice
|